![]() Pool Ladders | Pool Rails | Installation Instructions CORE DRILL & GROUT DIRECTLY INTO DECKRecommended installation method for. All in- ground rails, railing and ladders to be installed permanently into a concrete slab. Anchor Sockets (SAFTRON ANCH- 1). See below for grouting installation instructions specific to Anchor Sockets. Notes. Core- drilling requires specialized tools. Professional installation is recommended. (Not for the average “do- it- yourselfer”). Rails and ladders will only be as rigid and secure as the supporting foundation. Before installing, make sure the deck is suitable. Avoid scratches. Keep railings in box until ready to install. Don’t place railings on bare ground. Clean spills immediately with wet rag. Don't allow spilled grout to set on railings or deck. Tools & Materials Required. Diameter Core Bit. PSI Non- shrink Hydraulic Grout. Mixing Bucket. Wooden wedges. Tape Measure, Markers, String- Line & Adhesive Tape. Sponges, Rags, Water, Soft Scrub®Installation Steps. ![]() The web's choice for low-cost pool supplies! Poolweb carries everything needed to run a pool that you'll love to use. Pumps, pool automation, thermal blankets, ADA.We sell the 20' x 40' x 31' Lagoon Inground Swimming Pool Kit with 42'' Polymer Walls at wholesale prices! We strive to offer the best deal available and provide the. Above Ground Swimming Pool Ladders and Steps Smart Step System for 48"/52" above ground pools. To buy this ladder/step combination head to our new site, just click. Swimming pool parts for pumps, filters, cleaners, heaters. Hayward parts, Polaris parts, Pentair parts. Thousands of replacement pool and spa parts for pool equipment. Measure and mark installation location of railing posts. IMPORTANT: WHEN INSTALLING LADDERS, THE HORIZONTAL DISTANCE FROM FACE OF POOL WALL TO MOUNTING POST MUST BE CORRECT TO ENSURE SECURE FIT. REFER TO DIMENSION DRAWINGS FOR YOUR MODEL OF RAIL OR LADDER ON THIS WEB SITE TO DETERMINE REQUIRED DISTANCE. Drill 3" diameter x 4" deep core in concrete for each post location. If escutcheons are being installed, slide them onto the posts at this time and secure them with tape away from the base. Fully insert rail or ladder into holes and make sure it is properly aligned and level. LADDER BUMPERS MUST REST SQUARELY AGAINST POOL WALL FACE. Insert small wedges (i. Fill hole half way with grout. Re- check for alignment then wait for grout to set. Once grout has set, remove the wedges and finish filling the hole with grout. Lower escutcheons to cover grout perimeter. DO NOT USE RAIL UNTIL GROUT HAS FULLY CURED. Rails can be cleaned and polished using a soft rag and household Soft Scrub®. DO NOT USE ABRASIVES OR COMMERCIAL SOLVENTS. EZ ANCHOR SOCKET (Groutless / Core Drill)Recommended installation for. Rails, ladders, safety railings, posts, stanchions, umbrellas, flagpoles, volleyball net posts, etc… that have 1. OD mounting posts that need to be removable (i. Notes. The EZ Anchor Socket installs without grout, but it still requires a 3” diameter hole to be drilled to a depth of 4”. Core- drilling requires specialized tools. Professional installation is recommended. (Not for the average “do- it- yourselfer”). Rails and ladders will only be as secure as the supporting foundation. Before installing, make sure the mounting surface is suitably rigid and strong. Avoid scratches. Keep rails or ladders in box until ready to install. Don’t place on bare ground. Tools & Materials Required. Diameter Core Bit. Tape Measure & Pencil or Marker. Medium Phillips Head Screwdriver. Installation Steps. Measure and mark the CENTER of the desired mounting location of each rail or ladder post. This will be the CENTER of your core hole. Unlike traditional Anchor Sockets, the center of the EZ Anchor Socket is also the center of the installed post). IMPORTANT: WHEN INSTALLING LADDERS, THE HORIZONTAL DISTANCE FROM THE POOL WALL FACE (NOT THE COPING) TO THE CENTER OF THE MOUNTING POST MUST BE CORRECT TO ENSURE A SECURE FIT. REFER TO DIMENSION DRAWINGS FOR YOUR MODEL OF RAIL OR LADDER ON THIS WEB SITE TO DETERMINE THE REQUIRED DISTANCE. Drill a 3” diameter core in concrete to a depth of 4” for each anchor socket. VERY IMPORTANT: THE ANGLE OF THE DRILLED HOLE WILL DETERMINE THE ANGLE OF THE INSTALLED LADDER OR RAIL. BE SURE TO DRILL STRAIGHT. USE A DRILL WITH A BUBBLE LEVEL. A CROOKED HOLE WILL RESULT IN A CROOKED RAIL OR LADDER. OPTIONAL: IF INSTALLING STEEL RAILS THAT REQUIRE GROUNDING (Saftron Rails are non- conductive and do not require Grounding/Bonding): Attach grounding/bonding wire to grounding terminal on underside of the anchor socket between washers, then tighten the screw. Insert Anchor Socket(s) in cored holes, slide escutcheons onto posts and slide posts into anchor sockets until fully seated in the cavity. If necessary, loosen bolts on anchor socket to increase opening size before inserting post). Making sure both outer halves of the Anchor Socket are at the same starting height, use a Philips head screwdriver to tighten both screws by turning clockwise. Alternate ½ a turn at a time on each bolt until both are tight, then lower the escutcheons to cover the anchor socket. Rails can be cleaned and polished using a soft rag and household Soft Scrub®. DO NOT USE ABRASIVES OR COMMERCIAL SOLVENTS. TO REMOVE RAILS: Loosen both bolts by turning anti- clockwise then lift rail or ladder. Anchor socket can be removed the same way. SAFTRON ANCH- 1 ANCHOR SOCKET (CORE DRILL & GROUT)Recommended installation method for. Rails, ladders, safety railings, posts, stanchions, umbrellas, flagpoles, volleyball net posts, etc… that have 1. OD mounting posts, and that need to be removable (i. Notes. Core- drilling requires specialized tools. Professional installation is recommended. (Not for the average “do- it- yourselfer”). Rails and ladders will only be as rigid and secure as the supporting foundation. Before installing, make sure the deck is suitable. Avoid scratches. Keep railings in box until ready to install. Don’t place railings on bare ground. Clean spills immediately with wet rag. Don’t let spilled grout set on railings or deck. Tools & Materials Required. Diameter Core Bit. PSI Non- shrink Hydraulic Grout. Mixing Bucket. Tape Measure, Markers, String- Line & Adhesive Tape. Sponges, Rags, Water, Soft Scrub®. Saftron P- JIG- L or P- JIG- RTD (Optional). Wrench or Socket. Installation Steps. Measure and mark desired location of rail or ladder posts. Determine required location of Anchor Socket to achieve post location. NOTE: CENTER OF ANCHOR SOCKET IS NOT CENTER OF POST. DRAWING BELOW SHOWS DIMENSIONS. PDF FILE DRAWING PRINTED ON 8” X 1. PAPER CAN BE PRINTED AND USED AS TEMPLATE. CLICK HERE TO DOWNLOAD SCALE DRAWING IN PDF FILE FORMAT IMPORTANT: WHEN INSTALLING LADDERS, THE HORIZONTAL DISTANCE FROM THE POOL WALL FACE TO THE MOUNTING POST MUST BE CORRECT TO ENSURE SECURE FIT. REFER TO DIMENSION DRAWINGS FOR YOUR MODEL OF RAIL OR LADDER ON THIS WEB SITE TO DETERMINE REQUIRED DISTANCE. Drill TWO overlapping 3” diameter cores in concrete to a depth of 4- 1/4” – 4- 1/2” for each anchor socket location as shown on above template and as illustrated below. DO NOT MAKE HOLES LARGER THAN NECESSARY OR ESCUTCHEONS MAY NOT COVER ENTIRE GROUTED AREA. Tape over hole in base cover of anchor socket. Attach and firmly seat anchor socket(s) to Saftron P- JIG- L or P- JIG- RTD Jig, and tighten bolt (or use any other method to ensure proper alignment). OPTIONAL: IF INSTALLING STEEL RAILS THAT REQUIRE GROUNDING (Saftron Rails are non- conductive and do not require Grounding/Bonding). Attach grounding/bonding wire to connection terminal on side of anchor socket between washers, then tighten bolt. Place Anchor Socket(s) in grout holes. Re- check position and alignment. Secure in place with wood wedges. Fill void around anchor socket(s) with non- shrink, 7- 1. PSI hydraulic cement (grout). Once grout has fully cured, remove jig, insert rail or ladder, and securely tighten fastening bolt. DO NOT OVER- TIGHTEN. DO NOT USE RAIL UNTIL GROUT HAS FULLY CURED. Rails can be cleaned and polished using a soft rag and household Soft Scrub®. DO NOT USE ABRASIVES OR COMMERCIAL SOLVENTS. ANCH- 1 ANCHOR SOCKET USE: TO INSTALL RAILS. Use ½” wrench or socket to lower wedge about ½” inside socket by turning bolt counterclockwise. WARNING: TOO MANY TURNS WILL DISENGAGE WEDGE FROM BOLT. Insert rail or ladder post into Anchor socket. Tighten by turning bolt clockwise until secure. DO NOT OVER- TIGHTEN. TO REMOVE RAILS. Use ½” Wrench or Socket. Turn Counterclockwise a few turns. NOTE: TOO MANY TURNS WILL DISENGAGE WEDGE FROM BOLT. If bolt head rises after a few turns, tap bolt head down. Remove rail. SAFTRON SB- 3 & SB- F BASE SUPPORTSRecommended installation method for. Pool Rails, Pool Ladders & Pool Slides with 1. OD mounting posts. Can be used to surface- mount pool ladders and handrails to concrete or wood pool deck surfaces, or to (sturdy) steps such as those used with above- ground spas. Notes. Bases install quickly with common household tools. Leave minimal damage when removed. Suitable for use on wood or concrete decks.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
November 2017
Categories |